Compaq armada 1700 manual pdf

What screen dimensions does my Laptop have? The size of your Laptop is usually expressed in inches, 1 inch is 2. The size is the diagonal size of your Laptop, so you measure the screen from bottom left to top right.

What is HDMI? An HDMI cable is used to transport audio and video signals between devices. How can I best clean my Laptop? A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

The computer serial number should be provided to Compaq support when requesting information or ordering spare parts. The serial number is located on the back of the computer Figure Page 77 Refer to the disassembly steps before disassembling the computer. Disassemble only the components necessary to gain access to the sub-assembly you are servicing. Page 78 Before beginning the removal and replacement procedures, complete the following: 1.

Disconnect the modem line cord. Disconnect the AC power and any external devices. Remove the battery pack s. Remove the MultiBay device. Remove any PC Cards. Before beginning service procedures on the computer, remove all power from the system to prevent damage to the equipment or personal injury. Page 79 Remove the battery pack before beginning any internal maintenance on the computer.

To remove the battery pack from the computer, complete the following steps: 1 Slide the battery release latch 2 Remove the battery pack. The device in the MultiBay must be removed prior to performing maintenance on the computer. For convenience, a diskette drive is depicted in this sequence.

To remove any MultiBay device, complete the following steps: 1. To remove a PC Card, complete the following steps: 1. To release the PC Card eject button, depress the button once 2. Page 82 There are two tilt feet on the bottom of the computer.

To remove a foot, follow the steps listed. Turn the computer bottom side up and position it so that the front of the unit is toward you. Open the foot to the fully extended position. Page Internal Modem The internal modem is standard on some models and is attainable as an upgrade option on other models.

If the model is not equipped with a modem, the modem compartment is sealed by a protective plate underneath the modem cover. For models equipped with a modem, complete the following steps to remove the modem. Page 84 5.

Remove the modem board retaining screw. Carefully pull the modem board release tab and lift the modem from the computer. To replace or install the modem, reverse the procedure.

When installing the modem, be sure that the modem release tab is folded on top of the modem before replacing the modem access door. Page 85 To remove the Infrared IR transceiver module: 1.

Prepare the computer for disassembly Page Remove the modem Page Remove the screw from the IR module 4. Disengage the connector from the system board by lifting the corner of the IR module with a screwdriver. Page Hard Drive The hard drive is held in place with a security screw and a retaining bracket.

To remove the hard drive, complete the following steps: 1. Page 87 4. Slide the release latch toward the back of the computer. The cover lid springs open 5. Slide the hard drive cover toward the front of the computer 6. Lift the cover from the computer. Page 88 7. Disengage the hard drive from the connector by sliding the hard drive toward the front of the computer.

Using the lifting tab, remove the hard drive from the computer. Reverse the above procedure to install the hard drive. Be sure to place the lifting tab inside the computer before replacing the cover. Page Keyboard To release the keyboard, complete the following procedures.

Place the computer on the workspace with the front of the unit facing you. Open the display to the vertical position. To release the keyboard, insert the tip of the scribe into each of the keyboard holes, and pull the free end of the scribe towards you.

Page 90 6. Lift the keyboard. Place the keyboard in an upright position. Insert the two tabs on the right side and the tab on the left side of the keyboard into the slots provided on the right of the base enclosure. Page 91 1. Release the latch on the keyboard ZIF connector.

Slide the strain relief on the flat cable toward the back of the computer, then lift the front edge of the strain relief from the recess. Disconnect the keyboard ribbon cable. Page 92 If a memory expansion board option has been previously installed in the computer, it must be removed before another is installed. To remove the memory board, complete the following steps: 1. Lift the the keyboard as described Page Page 93 5. Rotate the free edge of the memory module upward.

At a 45 degree angle, pull the memory module from the slot. Armada Compaq Armada User Manual Download for 1. SuperDisk LS Drive or. Zip Drive. Hard Drives.

Ethernet Convenience Bases. Warranty with second business. Power Button 2. Microphone 3. Integrated AC Adapter 5. Processor Board 6.

TV Out 7. USB Port 8. Li-Ion Battery Pack Some settings may not take effect until the computer is restarted. Ignore—Exits Computer Setup and restores previous settings. Cancel—Returns to Computer Setup. Compaq Utilities contain several functions that Determine if various computer devices are recognized by the system and are operating properly. Page Compaq Diagnostics is a utility that inspects computer hardware, internal system temperature, and the SMART hard drive, then displays a prefailure warning message upon detecting a system temperature or hard drive fault.

If you are running Windows 95, access Compaq Diagnostics for Windows as follows: 1. Page Computer Checkup TEST determines whether the various computer components and devices are recognized by the computer and are functioning properly. You can display, print, or save the information generated by Computer Checkup.

Plug the computer into an external power source. A low battery condition could interrupt the program. You can display, print, or save the information. Page It is recommended that you use a backup program to create a backup of the preinstalled software. However, for an additional cost, you can order a backup of the preinstalled software on a CD- ROM or on diskettes.

If an order form is included with your computer, complete the form and return it, or call one of the numbers listed on the order form. Page chapter If you encounter a minor problem with the computer or software applications, go through the following checklist for possible solutions: Is the computer connected to an external power source or does it have a fully charged battery pack installed? Is the computer turned on and is the power light on? Are all cables connected properly and securely?

Did the diskette drive contain a nonbootable diskette when Page While your computer is configured just for you, problems you encounter while working may not be unique.

Eliminating the typical problems described in these troubleshooting sections may save you time and money. If you have a problem with your computer, consider the problems and possible solutions in the troubleshooting section.

Page External microphone You are using the does not work wrong type of microphone or microphone plug for the computer. The microphone may not be connected properly.

Sound source not selected. No sound is coming Audio settings are not from the game set correctly. Page Computer is beeping The computer has and battery charge entered a low battery light is blinking condition. Troubleshooting Save your information, exit all applications, and turn off the computer. If available, immediately connect the computer to an external power source.

If an external power source is not available, in Windows 95, initiate Immediately connect the computer to an external power source. If an external power source is not available and you are running Windows 95, be Page Battery pack will not Battery pack was fast charge exposed to tempera- ture extremes. Battery pack has exceeded its useful life.

Battery pack is already fully charged. Computer shut down You removed a and information was battery from the lost when replacing computer when the a battery pack computer had no The CD has been loaded upside down. The CD may be dirty or scratched. Cannot eject CD is not properly compact disc loaded in the drive.

Diskette drive light Diskette is damaged. Page Diskette is damaged. If you are running Windows Diskette drive light stays on Diskette is incorrectly inserted. Diskette drive cannot Diskette is not write to a diskette formatted. Diskette is write- protected. Computer is writing to the wrong drive. Not enough space is left on the diskette. Page Diskette drive cannot Diskette is not read a diskette formatted or is formatted incorrectly.

You are using the wrong type of diskette for the drive. Error message Diskette was appears while removed while drive information is writing light was on. Page Reading the hard Computer entered drive takes an Hibernation due to a unusually long time low battery condition after restarting the and is now exiting computer from it.

Hard drive error Hard drive has bad occurs sectors or has failed. Troubleshooting Give the computer time to restore the previously Page Hardware devices The system did not are not working automatically properly configure the new device. Cable s of the new external device may be loose or the power cable may be unplugged.

The power switch of the new external device is not turned on or was turned on after the computer was turned on. Page Embedded numeric Num Lock function is keypad on the off.

External keyboard You connected the does not work external keyboard while the computer was still turned on. Memory counting Memory board is during Power-On Page Modem loses The connection from connection the phone line to the modem is loose. Call Waiting has not been disabled. Hibernation was initiated or a low- battery condition occurred. Disconnect, then reconnect the phone cable. Reestablish connection. To disable Call Waiting: 1.

Page No dial tone Phone service is not connected to the telephone wall jack. Phone is connected to a digital PBX jack. Troubleshooting Continued Verify service from the local phone company by the following steps: 1. Unplug the 2. Connect a telephone Plugging the modem into a digital line will result in no dial tone. Page The modem is not responding to commands from the computer keyboard.

Verify the modem and computer are connected: 1. Unable to connect The site called does the internal modem not support 56K or at speeds above supports an PC Card beeps are disabled. The PC Card device drivers for your card are not installed. Page Card is not fully Computer beeps inserted into the slot only once when a or is upside down. PC Card is inserted Card is not recognized by the system. Card did not configure because of a conflict with another device in the computer.

The card is not formatted. The card is not supported by the computer. Computer turned off The system initiated while it was left Hibernation due to a unattended and low battery condition. Page Printer will not turn The cables may not be connected properly or the printer is unplugged.

Printer will not print Printer is not turned Printer is not online. The printer drivers for the application are not installed. Printer is offline Paper tray is empty. Screen save was initiated. Screen is blank and Suspend is initiated. Page Screen is blank and The computer has no lights are on either entered Hibernation or, if Hibernation is disabled, the battery pack has discharged without saving your information.

Screen is blank and QuickLock and keyboard is locked QuickBlank were initiated. These security features lock the keyboard and pointing device and Page Most software application or installation problems occur as a result of one or more of the following: The application was not installed correctly.

Memory was not allocated correctly. A conflict exists between applications. Insufficient memory There is not enough to run application memory for the application.

Page External pointing The external pointing device is not working device was connected to the computer while the computer was on. Touchpad is not Incorrect or no device working driver is installed. Device driver is The wrong mouse is loaded but pointing selected. Page Cannot The required software communicate with is not running on both another computer computers. One computer does not have an IrDA- compliant infrared port.

The pathway between the infrared ports is obstructed, one port is more than 30 degrees plus or minus 15 degrees off the center line from the other, or the ports are more Page Cannot transmit data Direct sunlight, fluorescent light, or flashing incandescent light is close to the infrared connections.

There is interference from other wireless devices. A physical obstruction is in the way. One of the devices was moved during data transmission. The orientation of the units is incorrect.

Page External device The operating system connected to a USB limits external devices connector does not connected by USB to work two tiers which can include no more than two hubs on the first tier and no more than one keyboard and one pointing device on the first or second tier. Page appendix If you cannot solve a problem using the troubleshooting tips in this guide, you may need to call technical support. To receive the fastest possible solution when you call, run the Compaq diagnostics utilities and have the following available when you call: The computer Serial number on the bottom of the computer Page Locate your geographical area in the following table and use one of the telephone numbers for Compaq assistance.

If the number listed in your geographical region is not valid, refer to the Compaq website at www. General Information Numbers—Product information, technical assistance, and the location of your nearest Compaq authorized dealer, reseller, or service provider.

Page appendix Throughout these regulatory notices, Compaq products are referred to by their regulatory agency series numbers. Regulatory agencies worldwide use agency series numbers for product identification. Each approved product displays the assigned agency series number.

To ensure continued safe and reliable operation, use your portable computer only with the products listed below These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Box , Mail Stop Houston TX or call To identify your product, refer to the part, series, or model number found on the product.

If you have questions about your product that are not related to this declaration, please write Compaq Computer Corporation P. Use of electronic equipment aboard commercial aircraft is at the discretion of the airline.

Page In North America, dispose of nickel metal hydride or lithium ion batteries by taking advantage of the Compaq battery recycling program. You will be provided with a postage-paid battery pack mailer preaddressed to a reclamation facility where the metals are recycled.

Call the telephone number listed for your location in Appendix A for more information. Food and Drug Administration implemented regulations for laser products on August 2, These regulations apply to laser products manufactured from August 1, Compliance is mandatory for products marketed in the United States. Page When Installing Internal Components appendix A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components.

Before handling electrostatic-sensitive components, discharge static electricity by one of the methods described in this appendix. To prevent electrostatic damage to removable drives, observe these precautions: Before handling a removable drive, discharge static electricity by touching the unpainted metal surface or lug nuts on the Page Grounding Methods Before touching an electronic component, discharge static electricity by one of the grounding methods described later in this appendix.

If you must leave the area during installation, remember to reground yourself before resuming installation. Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.

This computer operates well within this range of temperatures. See keyboard alerts system. See software arrow keys location of the. See keyboard AT commands.